![toyota diagnostic codes b2795 toyota diagnostic codes b2795](http://www.toyotagtturbo.com/wiki/EMBerrorcodes/em_errorcodes2.png)
switch on the ignition and wait at least 6 seconds connect two wires to the terminals "TC" and "AB" If the codes are saved, you need to perform the cleaning procedure: The self-diagnosis codes are read out in the same way as the others, in terms of the number of flashes of the "SRS" indicator when the terminals "TC" - "CG" (13-4) of the DLC3 connector under theĭashboard are closed and the ignition is switched on.Įrasing codes must occur when the ignition is switched off.
![toyota diagnostic codes b2795 toyota diagnostic codes b2795](http://img.autorepairmanuals.ws/images/2014/06/10/Toyota_Avanza_F601RM_Series_Electrical_Wiring_Diagram.jpg)
#Toyota diagnostic codes b2795 code#
The indicator should output the normal code (flashing 2 times per second).ġ2 - Relay e / m valve (short circuit in the chain)ġ4 - Electropump relay (short circuit in the circuit)Ģ1 - Front left right-hand wheel (open or short-circuited)Ģ2 - E / m front left-hand wheel valve (open or short-circuited)Ģ3 - E / m rear right wheel valve (open or short circuit)Ģ4 - E / m the valve of the rear left wheel (breakage or short circuit)ģ1 - Front right-wheel speed sensor (fault)ģ2 - Front left wheel speed sensor (fault)ģ3 - Rear right wheel speed sensor (fault)ģ4 - Rear left wheel speed sensor (fault)Ĥ3 - Deceleration sensor (fault in the circuit)Ĥ4 - Deceleration sensor (open or short circuit in the circuit)ĥ1 - Power supply circuit of the electric pump (open or short circuit in the circuit)ħ1 - Right front wheel speed sensor (low signal level)ħ2 - Left Front Wheel Speed Sensor (Low Signal)ħ3 - Rear right-wheel speed sensor (low signal level)ħ4 - Left rear wheel speed sensor (low signal level)ħ5 - Front right-hand wheel speed sensor (incorrect signal change)ħ6 - Front left wheel speed sensor (incorrect signal change)ħ7 - Rear right wheel speed sensor (incorrect signal change)ħ8 - Rear left wheel speed sensor (incorrect signal change) Depress the brake pedal eight or more times in the interval of three seconds.
![toyota diagnostic codes b2795 toyota diagnostic codes b2795](https://servicemanuals.online/1373/toyota-avensis-service-manual-repair-manual.jpg)
![toyota diagnostic codes b2795 toyota diagnostic codes b2795](https://img.autorepairmanuals.ws/images/2018/08/18/Toyota_Lexus_2018_Electrical_Wiring_Diagram_CD4.jpg)
Remove the jumper from the terminals "TC" and "CG". After 4 seconds, read the code by the number of indicator flashes. Connect the "TC" (13) and "CG" (4) terminals of the DLC3 connector. Reading codes (models with DLC3 connector) (OBD-II) (In this case, the upshift is to be enabled - "O / D OFF" is not lit).ģ7 - Input speed sensor for automatic transmission (P1705)ģ8 - The gauge of temperature of a working liquid АКППĤ2 - Speed sensor (or output speed sensor) (P0500)Ĥ4 - Speed sensor (or rear output speed sensor)Ĥ6 - Pressure accumulator pressure control solenoid (P1765)Ħ1 - Speed sensor (or front output speed sensor)Ħ4 - Torque converter lock solenoid (P0773)Ħ7 - Input speed sensor for automatic transmissionĦ8 - Torque converter clutch control solenoidħ3 - Interaxle differential lock solenoid "TC" - "CG" (13-4) of the DLC3 connector under the dashboard and the ignition on The self-diagnosis codes are read by the number of flashes of the "O / D OFF" indicator when the terminals are closed 13 - Crankshaft Position Sensor (P0335, P1335)ġ4 - Ignition system, coil No.